Extraction

Technology
Technology details
Name:
Category:	Pre-processing (Separation technologies), Post-processing (Separation technologies)
Feedstock:
Product:

Extraction is a separation process consisting of the separation of a substance from a matrix. Common examples include liquid-liquid extraction, and solid phase extraction. The term washing may also be used to refer to an extraction in which impurities are extracted from the solvent containing the desired compound.

Feedstock

Origin and composition

Extraction can be used to separate a valuable substance from the feed stream.

Process and technologies

Fluid-fluid extraction has various possible implementation forms on an industrial scale. Two main categories can be distinguished:

The first category consists of mixers-remixers (mixer-settlers), where the extraction process consists of two separate steps. In the first step, the two liquids are mixed to enable substance transfer. In the second step, the two liquids are separated. The two steps can take place in separate reactors.

The second category uses columns in which the two liquids are in continuous contact with each other. Here, typically special measures are taken to increase the contact surface between the feed and extraction flow (e.g. dispersion of one liquid, use of trays or packing material, ... ).

Liquid-liquid extraction is a process that separates substances based on their chemical properties. The principle consists of bringing the contaminated feed flow into contact with a second fluid, i.e. the extraction fluid. The extraction fluid is chosen in such a way that it does not mix with the supply flow and that it dissolves the pollutant well. During the extraction process, the contamination of the supply flow will (partially) transfer to the extraction fluid, until a balance in concentration has been reached. This balance depends on the affinity the pollutant has for the extraction fluid. If several substances are present, the balance will be substance-dependent. In an additional step, the pollutant is separated from the extraction fluid so it can be reused.

Technology providers

Technology comparison

Company name	Country	Technology category	Technology name	TRL	Capacity [kg/h]	Extractable substance	Feedstock: Food waste	Feedstock: Garden & park waste
Company 1	[Country HQ location]	[Technology category (if different sub-categories are defined this has to be specified here, the available categories can be found on each technology page under the chapter Process and technologies)]	[Technology name (the "branded name" or the usual naming from company side)]	[4-9]	[numeric value]		●	●
Company 2	[Country HQ location]	[(if different sub-categories are defined this has to be specified here, the available categories can be found on each technology page under the chapter Process and technologies)]	[Technology name (the "branded name" or the usual naming from company side)]	[4-9]	[numeric value]		●	●

ABC

[Technology name] provider

General information
Company:
Country:
Contact:
Webpage:
Technology and process details
Technology name:		Technology category:	Pre-processing (Separation technologies), Post-processing (Separation technologies)
TRL:		Capacity:	kg·h-1
Extractable substance:		Other:
Feedstock and product details
Feedstock:		Product:

describe the company, here is an example

ABC was founded in 20... 12 by KNN and Syncom, in collaboration with the university of Groningen, Netherlands. The company is a technology provider developing chemical recycling technologies for different feedstocks including non-food bio- and plastics waste. In 2018 a pilot plant with the capability to process biomass and plastic waste was set up at the Zernike Advanced Processing (ZAP) Facility. The company is now focused on setting up their first commercial plant with a capacity of 20,000 to 30,000 tonnes. The investing phase B was recently completed, with the last investment phase in 2019 the financial requirements are fulfilled to complete the commercialisation activities to build the plant which is expected for 2023.

describe their technology, here is an example

The technology is based on an Integrated Cascading Catalytic Pyrolysis (ICCP) process, being able to produce aromatics including benzene, toluene, and xylene (BTX) as well as light olefins from low grade biomass and plastics waste. This technology utilises catalytic cracking in a two-step process at temperatures between 450- 850 °C. In the first step the feedstock material is vaporised via thermal cracking. The pyrolysis vapours are then directly passed into a second reactor in which they are converted into aromatics by utilising a zeolite catalyst which can be continuously regenerated. Finally, the products are separated from the gas via condensation. An ex situ approach of catalytic conversion has several advantages such as the protection of the catalyst from deactivation/degradation expanding its lifetime, a greater variety of feedstock, and a precise adjustment of process conditions (e.g. temperature, catalyst design, and Weight Hourly Space Velocity (WHSV) in each step for improved yields. In current pilot plant with 10 kg h-1 feed capacity for either waste plastics or biomass, final design details are established, which will be include in the running engineering activities for the commercial plant.

Open access pilot and demo facility providers

Pilots4U Database

Patents

Currently no patents have been identified.